; File QBLAZER.SCR (MSMQBLAZ.SCR)
;
; An MS-DOS Kermit script program for dialing Telebit QBlazer modems.
; Set up QBlazer for compression, error correction, all types of fallback,
; RTS/CTS flow control, fixed interface speed of 38400.
;
; Requires MS-DOS Kermit 3.12 or later
;
; Authors: Christine M. Gianone, Frank da Cruz; Columbia U, June 1993
;
def errfail echo \%1, hangup, goto fail ; Macro to handle failures.
if < VERSION 312 errfail {MS-DOS Kermit 3.12 or later required.}
if eq "\v(system)" "UNIX" if = \v(local) 0 stop 1 Please SET LINE first.
define chkerr if fail stop 1 \%1
define chkok input 3 OK, if fail stop 1 \%1
define max_speed 38400 ; Change these two if necessary
define s51 6 ; ...
; Macro to try to get attention of modem's command processor
; at the given speed, or if no speed given, at the current speed.
;
define atok -
if not def \%1 assign \%1 \v(speed), -
set speed \%1, -
echo Trying \%1..., -
output \B, -
output \17, -
output ATQ0\13, -
input 3 OK, -
if success goto gotok
set input echo on ; So we can watch what happens.
set input timeout proceed ; Allow IF SUCCESS, IF FAILURE.
set input case ignore ; Use caseless string comparisons
set parity none ; Avoid parity foulups
set flow none ; Avoid flow control deadlocks
hangup ; Begin by dropping DTR
pause 1 ; for one second
echo Configuring Telebit QBlazer on \v(line).
if > \v(speed) \m(max_speed) set speed \m(max_speed)
atok ; Try to connect at current speed, whatever it is.
atok 9600 ; Try to connect at 9600.
atok 19200 ; 19200...
atok 2400 ; etc...
atok 38400 ; Last resort because no autobaud at this speed(?)
stop 1 Can't get modem's attention
; QBlazer modem setup, should apply to all connections:
;
; X4 Result code selection, wait for dialtone, recognize busy signal.
; &D2 Disconnect call and return to command mode if DTR drops;
; this allows HANGUP to work if cable properly wired.
; S50=0 Automatic modulation speed determination.
; S94=1 Allow connection at any speed and allow modulation fallback.
; S58=2S68=255 Use RTS/CTS hardware flow control.
; S60=0 Data format: 8 data bits, no parity.
; S61=0S63=0 Pass BREAK through transparently.
:GOTOK ; Got OK from modem
;;output AT&F\13 ; Restore factory settings (no, this changes speed!)
;;chkok {Can't restore factory settings}
output AT E1 Q0 V1 &D2 S59=15 X4\13 ; Set echo and response modes.
chkok {Can't initialize modem}
echo Locking interface speed at \m(max_speed)...
output ATS51=\m(s51)\13
chkok {Can't set modem's speed to \m(max_speed)}
set speed \m(max_speed)
; Try 3 times to get OK response to AT at new speed.
;
set count 3
:LOOP
pause
output AT\13
input 3 OK
if success goto ok
if count goto loop
Stop 1 Can't communicate with modem at \m(max_speed)
:OK
echo Enabling hardware flow control...
output AT S58=2 S68=255 &R3\13 ; Tell modem to use RTS/CTS
chkok {Can't enable RTS/CTS}
wait 5 cts
if fail errfail {Modem is not asserting CTS!}
set flow rts/cts ; Tell Kermit to use RTS/CTS
echo Enabling modulation negotiation...
output AT S50=0 S94=1\13 ; Enable modulation speed negotiation
chkok {Can't enable modulation speed negotiation}
echo Configuring modem to ignore BREAK...
output AT S60=0 S61=0 S63=0\13 ; Make modem ignore break
chkok {Can't be transparent to BREAK}
echo Enabling error correction and data compression...
output AT S180=2 S181=1 S190=1\13 ; Enable error correction & compression
chkok {Can't enable compression EC and fallback}
if def \%1 if not equal "\%1" "=" goto BEGIN
echo QBlazer initialized OK:
output AT&V\13
input 10 OK
echo
echo Firmware version:
output ATI3\13
input 4 OK
end 0
:BEGIN ; Now DIAL.
clear ; Clear INPUT buffer.
set count 5 ; Dialing retry counter, 5 tries allowed.
echo Dialing \%1 on \v(line) at \v(speed) bps, wait...
echo
pause 1
goto dial ; 1st time, skip pause and Redialing message
:REDIAL
set alarm 30
pause 30 ; Wait 30 seconds before redialing.
if not alarm errfail {Dialing canceled.}
echo Redialing... ; Message for redialing.
pause 1
:DIAL
output ATD\%1\13 ; Dial the number.
set alarm 90 ; (For detecting keyboard interruptions.)
if > VERSION 312 clear input ; Clear echo from INPUT buffer.
if < VERSION 313 clear
pause 1 ; Wait a sec
input 30 \10 ; Wait for the linefeeds...
:GETMSG
input 60 \10 ; ...that surround the response message.
if success goto gotmsg ; Got a message.
if alarm errfail {No response from modem.} ; No response in 90 seconds.
hangup ; User interrupted from keyboard,
output \13 ; cancel dialing by sending carriage return,
goto again ; and go try again right away.
:GOTMSG
reinput 1 CONNECT ; Got a message, was it CONNECT?
if success goto done ; If so, we're done.
reinput 1 DIALING ; Modem says it's dialing...
if fail goto g2
if > VERSION 312 clear input ; Clear echo from INPUT buffer.
if < VERSION 313 clear
goto getmsg ; message again, then go get next message.
:G2
reinput 1 RRING ; Remote phone is ringing...
if fail goto g3
clear ; Clear INPUT buffer.
goto getmsg ; Go wait for another message.
:G3
reinput 1 BUSY ; Line is busy.
if success goto busy ; Go wait a while and then dial again.
:G4
reinput 1 ERROR ; Command syntax error.
if success errfail {Dialing command error}
reinput 1 NO CARRIER ; Phone didn't answer or no carrier.
if success errfail {No answer or no carrier}
reinput 1 NO DIALTONE ; No dialtone when phone taken off hook.
if success errfail {No dialtone - Is your modem connected to the phone line\63}
goto getmsg ; None of the above, get another message.
:BUSY
if < \v(count) 2 goto quit ; Don't wait 30 seconds if tries are used up.
echo Line is busy, will dial again in 30 seconds.
echo Press any key to cancel...
output \13 ; CR cancels dialing
hangup ; Hang up.
:AGAIN
if count goto redial ; Then go redial.
:QUIT
errfail {It never answers! I give up.} ; Too many tries.
:DONE ; Connected.
echo \7 ; Celebrate with a beep.
define errfail ; Erase local macro definitions...
end 0 ; Finished, return success code.
:FAIL ; Dialing failed, no beep.
define errfail ; Erase local macro definitions...
end 1 ; Return failure code.
; End of QBLAZER.SCR