txSerial Transmit enabled.
help
Nanometrics Trillium User Menu (Version 3.33) Program A
**********************************************************************
Help - Repeat this menu (also turns on Serial TX)
Tx - Enable the Serial Transmit Signal
TxOff - Disable the Serial Transmit Signal
Upload - Upload software to the alternate program
Switch - Switch to the alternate program
Default - Set the current program as default
Reboot - Reboot the instrument
GetInfo - Get factory configuration information
ReadFC - Read factory calibration parameters
WriteUC - Write user calibration parameters
ReadUC - Read the user calibration parameters
Soh - Report state-of-health
ShortPer - Set sensor to short period mode
LongPer - Set sensor to long period mode
SetXYZ - Set sensor to XYZ mode
SetUVW - Set sensor to UVW mode
Center - Center all masses or (u/v/w)
CheckSum - Print checksum value for both program A and B
**********************************************************************
Please type a command and hit return:
soh
"Nanometrics, Inc."
"Trillium Firmware"
3.33
12.20
U=-1.886 V=-0.607 W=-3.324
U=-852 V=-274 W=-1502
Period=Long Channel=XYZ
U=67 V=172 W=317
U=-329 V=37 W=502
U=+/-7424 V=+/-7334 W=+/-7194
centermove=0, steps=0, per=3, pos=0, ADC=-848
move=1, steps=580, per=3, total steps=580, ADC=48
MC=CENTERED, Ch=U, Pos=647, Mass=0.105V, ADC=48
move=0, steps=0, per=3, pos=0, ADC=-272
move=1, steps=171, per=3, total steps=171, ADC=-6
MC=CENTERED, Ch=V, Pos=343, Mass=-0.014V, ADC=-6
move=0, steps=0, per=3, pos=0, ADC=-1589
move=1, steps=1004, per=3, total steps=1004, ADC=3
MC=CENTERED, Ch=W, Pos=1321, Mass=0.006V, ADC=3
soh
"Nanometrics, Inc."
"Trillium Firmware"
3.33
11.97
U=0.039 V=-0.023 W=0.012
U=18 V=-10 W=6
Period=Long Channel=XYZ
U=647 V=343 W=1321
U=-329 V=37 W=502
U=+/-7424 V=+/-7334 W=+/-7194
help
Nanometrics Trillium User Menu (Version 3.33) Program A
**********************************************************************
Help - Repeat this menu (also turns on Serial TX)
Tx - Enable the Serial Transmit Signal
TxOff - Disable the Serial Transmit Signal
Upload - Upload software to the alternate program
Switch - Switch to the alternate program
Default - Set the current program as default
Reboot - Reboot the instrument
GetInfo - Get factory configuration information
ReadFC - Read factory calibration parameters
WriteUC - Write user calibration parameters
ReadUC - Read the user calibration parameters
Soh - Report state-of-health
ShortPer - Set sensor to short period mode
LongPer - Set sensor to long period mode
SetXYZ - Set sensor to XYZ mode
SetUVW - Set sensor to UVW mode
Center - Center all masses or (u/v/w)
CheckSum - Print checksum value for both program A and B
**********************************************************************
Please type a command and hit return:
getinfo
Trillium120
BIN 16214
BOM 1
ASY 10
SN 1981
FBE
BIN ASM16136
BOM 02
ASY 02
SN 1925
ExtFlex
BIN CCA14933
BOM 04
ASY 04
SN 1931
AxisU
BIN ASM16210
BOM 04
ASY 04
SN 6544
FlexU
BIN ASM16219
BOM 04
ASY 04
SN 5264
AxisV
BIN ASM16210
BOM 04
ASY 04
SN 6554
FlexV
BIN ASM16219
BOM 04
ASY 04
SN 5453
AxisW
BIN ASM16210
BOM 04
ASY 04
SN 6558
FlexW
BIN ASM16219
BOM 04
ASY 04
SN 1931
#End
soh
"Nanometrics, Inc."
"Trillium Firmware"
3.33
11.90
U=0.030 V=-0.028 W=0.008
U=14 V=-12 W=4
Period=Long Channel=XYZ
U=647 V=343 W=1321
U=-329 V=37 W=502
U=+/-7424 V=+/-7334 W=+/-7194
help
Nanometrics Trillium User Menu (Version 3.33) Program A
**********************************************************************
Help - Repeat this menu (also turns on Serial TX)
Tx - Enable the Serial Transmit Signal
TxOff - Disable the Serial Transmit Signal
Upload - Upload software to the alternate program
Switch - Switch to the alternate program
Default - Set the current program as default
Reboot - Reboot the instrument
GetInfo - Get factory configuration information
ReadFC - Read factory calibration parameters
WriteUC - Write user calibration parameters
ReadUC - Read the user calibration parameters
Soh - Report state-of-health
ShortPer - Set sensor to short period mode
LongPer - Set sensor to long period mode
SetXYZ - Set sensor to XYZ mode
SetUVW - Set sensor to UVW mode
Center - Center all masses or (u/v/w)
CheckSum - Print checksum value for both program A and B
**********************************************************************
Please type a command and hit return:
txoffSerial Transmit disabled.